初始温度和压力对排污空间甲烷-空气混合物爆燃特性影响的模拟研究

市政排污空间作为城市公共基础设施的重要组成部分，易积聚可燃气体形成爆炸性环境。结合排污空间的特殊环境条件，采用Fluidyn-MP多物理场数值模拟软件，建立了20 L球形爆炸罐分析模型，通过改变初始温度和初始压力，对排污空间甲烷-空气混合物爆燃特性及其变化规律进行模拟研究。结果表明:初始温度升高导致甲烷-空气混合物最大爆炸压力降低，缩短了到达最大爆炸压力的时间；初始压力增加导致最大爆炸压力急剧升高，并延长了到达最大爆炸压力的时间；最大爆炸压力对初始压力的敏感程度远大于初始温度的影响。此外，随着初始温度和初始压力的升高，爆炸火焰平均传播速度增加，而火焰传播速度对初始温度较敏感。     

期权理论在排污权初始分配中的应用

排污权交易是当前总量控制目标下最具潜力的环境政策,它兼有环境质量保障和成本效率优化的特点.在对国内外排污权交易和初始分配充分考察的基础上,提出了在排污权初次分配中引入期权机制的尝试,并对这种方法的理论基础作了分析和讨论.     

降水和风对大气PM2.5、PM10的清除作用分析

对合肥2015—2017年的降水、风和PM_(2.5)、PM_(10)浓度观测数据统计研究发现,降水对PM_(2.5)、PM_(10)有一定的清除作用,尤其在秋冬季节.秋冬季节小雨、中雨分别导致PM_(2.5)和PM_(10)浓度降低23.1%、40.4%和32.0%、63.7%.雨日PM_(2.5)/PM_(10)比例上升8.4%,表明降水对PM_(10)清除作用更显著.降水前后PM_(2.5)浓度变化与降水前PM_(2.5)浓度、降水强度、降水时长密切相关.当降水强度大于4 mm·h~(-1)或PM_(2.5)初始浓度高于115μg·m~(-3)时,降水对PM_(2.5)产生明显清除作用;而降水强度小于1 mm·h~(-1)或PM_(2.5)初始浓度低于115μg·m~(-3)时由于吸湿增长作用极易造成PM_(2.5)浓度反弹升高;且持续3 h以上雨强介于1～4 mm·h~(-1)的降水也对PM_(2.5)产生清除作用.降水前后PM_(10)浓度变化与初始浓度密切相关,而与雨强相关性较弱.当PM_(10)初始浓度大于50μg·m~(-3),降水就对PM_(10)产生明显清除作用,且PM_(10)初始浓度越高,降水后PM_(10)浓度下降越多.风速大于2 m·s~(-1)可显著降低PM_(2.5)浓度,因此,当风速大于4 m·s~(-1)时合肥较少出现中度及以上污染,但易造成地面起尘,使PM_(10)浓度不降反升.合肥冬季严重污染主要出现在西北风向,夏季中度以上污染天气较少,主要出现在风速低于3 m·s~(-1)的东南风向.     

嘉兴市污水海洋处置工程扩散器长度的确定

为了能满足设计初始稀释度并降低工程费用，结合嘉兴市污水海洋处置工程，利用Jetlag3模型确定了其扩散器长度。计算结果表明，八团（0－1500）扩散器长度取200－250m，场前（0＋000）和场前（0＋1400）扩散器长度取250－300m，能满足近区初始稀释度的要求。     

SO2在碳钢初期大气腐蚀中的作用

通过自建的模拟大气腐蚀系统,借助金相显微镜、扫描电镜(SEM/EDX)、X-射线衍射(XRD)和x-射线光电子能谱(XPS),研究了SO2对碳钢初期大气腐蚀行为的影响,并进一步用原子力显微镜从更微观的角度观察了在SO2环境中初期阶段腐蚀形貌变化.研究结果表明:在SO2污染大气环境中,随SO2浓度的升高碳钢腐蚀加快.在体积分数为5×10(-6)SO2的大气环境中,碳钢和耐候钢表面腐蚀主要以条状物生长,随着SO2浓度的升高,腐蚀产物的形貌发生改变,在体积分数为5×10(-5)SO2的大气环境中,条状锈和胞状锈同时生长.在锈层中S元素以FeSO4·4H2O的形式存在,腐蚀产物中还有γ-FeOOH.SO2在初期阶段加速了碳钢的腐蚀,降低了碳钢的耐蚀性.     

降解蒽嗜盐菌AD-3的筛选、降解特性及加氧酶基因的研究

蒽是典型的多环芳烃类环境污染物,属于美国EPA优先控制的16种多环芳烃类化合物,其在高盐环境下的生物降解备受关注.本研究从某石油污染的高盐土壤中成功筛选出了1株高效降解蒽的菌株,经过对其生理生化特征和16S rDNA序列分析,初步鉴定并命名该菌株为Martelella sp.AD-3.该菌株在0.1%～10%的盐度和6.0～10.0的pH范围内,均能够降解蒽.其生长和降解蒽的优化条件是:蒽初始浓度25 mg·L-1、温度30℃、pH值9.0和盐度3%,在优化条件下培养6 d,蒽的降解率可达到94.6%.根据已报道的双加氧酶α亚基的同源性设计简并引物,通过巢式PCR扩增获得双加氧酶基因的部分序列307 bp(GenBank:JF823991.1),与海杆菌属Marinobacter sp.NCE312(AF295033)菌株萘双加氧酶大亚基的部分氨基酸序列同源性最高为95%.     

火车装油过程初期火灾扑救方法探讨

以敞口、小鹤管、人工装汽油为例,通过试验分析认为:通常采用的干粉灭火法从理论和生产实际来看都存在问题,细水雾法是适合火车装油过程初期火灾扑救的较好方法,具有安全高效的特点。     

Sludge concentration dynamic distribution and its impact on the performance of UNITANK

UNITANK is a biological wastewater treatment process that combines the advantages of traditional activated sludge process and sequencing batch reactor, which is divided into Tank A, B and C. In this study, the sludge distribution and its impact on performance of UNITANK were carried out in Liede Wastewater Plant （WWTP） of Guangzhou, China. Results showed that there was a strong affiliation between Tank A and B of the system in sludge concentration distribution. The initial sludge concentration in Tank A could present the sludge distribution of the whole system. The sludge distribution was mainly influenced by hydraulic condition. Unsteady sludge distribution had an impact on variations of substrates in reactors, especially in decisive reactor, and this could lead to failure of system. Settler could partially remove substrates such as COD and NO3-N, but there was adventure of sludge deterioration. The rational initial sludge concentration in Tank A should be 4000-6000 mg/L MLSS.     

张弦网壳结构索张拉模拟计算及试验研究

施工张拉控制是张弦网壳结构的关键技术之一,提出采用控制索原长的反分析方法追踪结构施工整个过程。首先,通过控制索在预应力状态下的张拉力求出零状态和索原长,并同时获得预应力态下所有单元的内力。在此基础上,通过控制每一级张拉索的原长,进行非线性有限元迭代计算,可求出索在分级分批施工时的控制力,并用VC＋＋6.0编制相应的计算程序。这一方法有效地避免了通用有限元需要反复试算,计算繁琐的缺点。最后,以张弦网壳结构模型为试验对象,按分级分批张拉的方式模拟结构的现场施工,并跟踪施工过程中杆件单元的应力状态。结果表明,数值模拟计算与试验值吻合较好,计算结果可靠,该方法能精确模拟结构的施工成形过程,且在整个过程中,每根索只需张拉一次,简化了施工工艺。     

A numerical study of summer ozone concentration over the Kanto area of Japan using the MM5/CMAQ model

We assessed the ability of the MM5/CMAQ model to predict ozone (O3) air quality over the Kanto area and to investigate the factors that a ect simulation of O3. We find that the coupled MM5/CMAQ model is a useful tool for the analysis of urban environmental problems. The simulation results were compared with observational data and were found to accurately replicate most of the important observed characteristics. The initial and boundary conditions were found to have a significant e ect on simulated O3 concentrations. The results show that on hot and dry days with high O3 concentration, the CMAQ model provides a poor simulation of O3 maxima when using initial and boundary conditions derived from the CMAQ default data. The simulation of peak O3 concentrations is improved with the JCAP initial and boundary conditions. On mild days, the default CMAQ initial and boundary conditions provide a more realistic simulation. Meteorological conditions also have a strong impact on the simulated distribution and accumulation of O3 concentrations in this area. Low O3 concentrations are simulated during mild weather conditions, and high concentrations are predicted during hot and dry weather. By investigating the e ects of di erent meteorological conditions on each model process, we find that advection and di usion di er the most between the two meteorological regimes. Thus, di erences in the winds that govern the transport of O3 and its precursors are likely the most important meteorological drivers of ozone concentration over the central Kanto area.